Before Takeoff

A/T	Arm
Fuel Flow	Reset
No Smoking Sign	On	If "Enable seatbelt signs check" option set to true
Seat Belts Sign	On	If "Enable seatbelt signs check" option set to true
Logo Lights	On	If dark
Position Lights	Strobe & Steady
Wing Lights	On	If "Enable wing lights ON" option set to true or is dark
Wheel Well Lights	Off
Taxi Lights	On or Off	On if "Taxi lights ON during takeoff" option set to true, otherwise off
Landing Lights	On L+R
Runway Turnoff Lights	On L+R
Transponder	TA/RA or TA	TA if "Set TCAS to TA Only" option set to true, otherwise TA/RA
Packs	Off	If "Set packs off" option set to true
Elapsed Timer	Start CPT+FO	If "Start Elapsed Timer" option set to true
Auto Landing Lights	Arm

After Landing

Speed Brakes/Spoilers	Retract	If "Enable speedbrake retraction" option set to true
Flaps	Up	If "Enable flaps retraction" option set to true
Transponder	XPNDR
Position Lights	Steady
Wing Lights	Off	If "Turn wing lights off" option set to true
Landing Lights	Off L+R
Runway Turnoff Lights	Off L+R	If "Turn runway turnoff lights off" option set to true
Taxi Lights	On
APU	On
Probe Heat	Off A+B
Engine Start Switch	Off L+R
Auto Brake	Off
Elapsed Timer	Stop CPT+FO	If "Stop Elapsed Timer" option set to true

Auto Landing Lights

• Automatically turn the landing lights and other lights off/on when passing through a certain altitude.
• You must ARM it by clicking on the widget, and it will turn orange. Then, while the airplane crosses the specified altitude, the actions will be triggered accordingly.
• Executing the Before Takeoff widget will arm this automatically. Don't forget to arm it again before descending.
• The altitude reported by MSFS might be different from the one shown on the PFD, so giving some margin is recommended.

	Off (ascending)	On (descending)	Specified by "Lights off/on altitude"
Landing Lights	Off L+R	On L+R
Runway Turnoff Lights	Off L+R	On L+R
Taxi Lights	Off	On
Logo Lights	Off	On	If dark
Wing Lights	Off	On	If "Enable wing lights ON" option set to true or is dark
Engine Start Switch	No Change	CONT L+R
Seat Belts Sign	No Change	On

Heading Sync

• The widget shows the current actual heading when idle, and the MCP heading when scrolling.
• Click on the widget to sync the MCP heading to the current heading.
• Scroll on the widget to change the MCP heading.
• Use OTTO to set the heading to a value. An example command would be "hdg 200".

Set MCP Course

• The widget shows the left (captain's) MCP course value.
• Clicking on the widget syncs the right (first officer's) MCP course value to the left.
• Scroll on the widget to change the left MCP course value.
• Use OTTO to set the left and right MCP course to a value. An example command would be "crs 270".

Set IAS

• The widget shows the current IAS/Mach speed (or a blank value) shown on the MCP.
• Scroll on the widget to change the MCP speed.
• Use OTTO to set (and intervene) the speed to a value. Some example commands would be "spd 180", "ias 180 intv", "mach 0.82", "spd intv", etc.

Set Altitude

• The widget shows the current MCP altitude.
• Scroll on the widget to change the MCP altitude.
• Use OTTO to set (and intervene) the altitude to a value. Some example commands would be "alt 3000", "fl 320", "fl 200 intv", "alt intv", etc.

Set Minimums

• Scroll on the widget to change the minimums value.
• Use OTTO to set the minimums to a value. Some example commands would be "mins 200", "baro 360", "radio 200", "mda 240", etc.
• NOT PRECISE. Since there is no way to verify the final value, this widget may end up with the wrong value.

Toggle Chocks

• Click on the widget to toggle chocks.